#Epson stylus photo 1280 manual serial
#Epson stylus photo 1280 manual manual

DISASSEMBLY / ASSEMBLY Describes the step-by-step procedures for disassembling and assembling the product. TROUBLESHOOTING Describes the step-by-step procedures for the troubleshooting. OPERATING PRINCIPLES Describes the theory of electrical and mechanical operations of the product. PRODUCT DESCRIPTIONS Provides a general overview and specifications of the product.

#Epson stylus photo 1280 manual manual

Manual ConfigurationThis manual consists of six chapters and Appendix. The instructions and procedures included herein are intended for experienced repair technicians, and attention should be given to the precautions on the preceding page. WHEN USING COMPRESSED AIR PRODUCTS SUCH AS AIR DUSTER, FOR CLEANING DURING REPAIR AND MAINTENANCE, THE USE OF SUCH PRODUCTS CONTAINING FLAMMABLE GAS IS PROHIBITED.ДЄbout This ManualThis manual describes basic functions, theory of electrical and mechanical operations, maintenance, and repair procedures of the printer. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE INTRODUCTION OF SECOND-SOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.

#Epson stylus photo 1280 manual serial

MAKE CERTAIN THAT THE SOURCE VOLTAGE IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN. WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH SHARP EDGES. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC COMPONENTS. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR REPAIR PROCEDURES. The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.ДANGER1. Signals a precaution which, if ignored, could result in damage to equipment. Great caution should be exercised in performing procedures preceded by DANGER Headings. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. PRECAUTIONSPrecautionary notations throughout the text are categorized relative to 1) personal injury and 2) damage to the equipment. Imaging Products CS, PL & Environmental Management

EPSON disclaims any and all rights in those marks.Д¬opyright 2006 SEIKO EPSON CORPORATION. General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their respective owners. The above not withstanding, SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.Д®PSON is a registered trademark of SEIKO EPSON CORPORATION. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them. All effort have been made to ensure the accuracy of the contents of this manual. The contents of this manual are subject to change without notice. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.